Winix Air Cleaner User Manual (Model 5500-2 )

Winix Air Cleaner User Manual
Air Purifiers

Use & Care  Guide

  • . Please read and follow all safety rules and instructions in this manual before operating.  
  • .The product warranty is printed on the back of this guide,  so please keep it in a safe place for future use. 
  • . This product is manufactured for use only in USA/CA 

This product is suitable for 120V only. 

3-STAGE AIR PURIFICATION 

READ ALSO: Blue Pure Blueair 311 Auto/411 Auto User Manual

CONTROLS 

WHERE TO USE 

Allow 12 ~ 18 in. of space between TVs, radios, and other electronic products electromagnetic interference from certain electronics may cause product malfunction. 

Place indoors away from direct sun light. direct exposure may cause product malfunction or failure. 

Only place on hard, flat surfaces flimsy or slanted surfaces may result in abnormal noise and vibrations. 

WARNING Follow these instructions to reduce the risk of serious  injury or death and to reduce risk of damaging the unit.
  • Do not use around mist or fumes from  industrial oil or around large quantities of  metallic dust 
  • Do not install in any sort of motor or  transport vehicle (trucks, boats, ships, etc.) 
  • Do not place near any flammable materials  (aerosols, fuel, gases etc.) 
  • Do not place below any electrical outlet 
  • Do not place around heating elements 
  • Do not place in an area with excessive  amounts of noxious gases 
  • Do not have unit facing into wind or draft 
  • Do not place in excessively humid areas  where unit may become wet 

※ This unit is not intended to be used to preserve documents or in art conservation.

INSTALLING FILTERS 

This product comes with all the required filters. The protective plastic  wrap must be removed from the filters before use 

※ Operating the unit without removing the plastic wrap may result in  product failure. 

※ Unplug and make sure the unit is turned off before installing filters. 

① Remove the front panel by grasping its upper edge and gently pulling  forward. 

 

② Remove the filters from the unit, they are protected inside a plastic wrap 

③ Remove filters from protective plastic wrap.    

•Operating the unit without removing filters from plastic wrap may cause abnormal noise, deformation, or fire as a result of  overheating. 

Note •Refer to relevant pages for details on how to replace filters. 

④ Install the filters until they fit securely in place. 

Filters must be installed in this order: 

3 True HEPA Filter (rear) 

2 AOCTM Carbon filter (middle) 

1 Pre-filter (front) 

•To install the Pre-filter, insert bottom  tabs into the slots on either side of the lower part of the unit, then rotate  upward to insert the upper tabs into the slots at the top part of the unit until  sides audibly click into place.  

⑤ Replace the front panel by first  inserting the latch at the bottom  edge into the base of the unit, then  rotate the panel upward toward the  top of the unit until the magnets  pull the lid closed. 

⑥ When to service and replace filters: 

Filter Indicator Light When to  service When to replace
Pre-filter none Clean once  every 14 days Permanent
AOCTM Carbon filter  check filter Clean once  every 3  months Lasts up to 12 months
True HEPA filter check filter Can NOT be  WASHED Lasts up to 12 months

※ Intervals between filter replacement may vary depending on environment. ※ For optimal use, Pre-filter can be cleaned once every 14 days which can extend  the life of other filters. 

To purchase replacement 

Winix filters: 

🕿(877)-699-4649 

www.winixamerica.com 

SAFETY AND CAUTIONS 

Before operating this equipment, carefully read and follow these safety  cautions 

  • Ensure filters are inserted before running unit 

running unit without filters can shorten the units life and cause electric shock or injury. 

  • Be sure foreign objects are NOT inserted into the vents on the unit

objects can include pins, rods, and coins.  

  • Do not touch any part of the interior of the unit with wet hands 

the high voltage may cause electric shock. 

  • Ensure unit intake and outlet vents do not become blocked 

blockage may lead to increased internal termperatures causing product failure and derformation. 

  • Do not use the unit as a step stool or place heavy objects on it 

personal injury may occur or product failure and deformation.

WARNING Follow these instructions to reduce the risk of serious  injury or death and to reduce risk of damaging the unit.
  • Do not pull on the power cord when  unplugging the unit 
  • If the unit becomes submerged in water,  unplug it and contact customer service 
  • Do not tie or knot power cord when unit is in operation 
  • Do not unplug or move the unit while in operation 
  • Do not touch the plug with wet hands
  • Do not plug additional appliances into the  same outlet or power supply 
  • Unplug unit when not in operation for  extended periods of time 
  • Cord can become damaged by forcefully  bending, pulling, twisting, bundling, pinching or placing heavy objects on it 

INITIAL OPERATION

① Insert the power cord into an electrical outlet.   

② Press the ‘Power’ button. 

Note 

•During the first 30 seconds of power up, the Air Quality  Indicator will cycle through Blue, Yellow and Red colors. The  Smart Sensors take approximately 4 minutes to gauge the air  quality in the environment, after which normal operation will  begin. 

③ By default, when the unit first powers on, the mode will be set to Auto with PlasmaWave® enabled.   

•When in Auto mode, the fan speed will be automatically adjusted according to the environments air quality.  

  •PlasmaWave® works to remove harmful airborne contaminants. 

Note 

•In Auto mode, as the indoor air quality improves, the fan  speed will automatically be reduced to Low. 

•When the unit is running, you may hear a chirping or buzzing  sound. The sound is from large particles passing through  PlasmaWave®, it is normal and does not signify product  failure. To disable PlasmaWave®, see relevant page

AUTO & SLEEP 

1. Auto Mode 

Enables auto operation based on the unit’s air quality Smart Sensors. 

① Press the Mode button to select Auto mode.  

•The LED ‘Auto’ light will indicate when Auto mode is activated, and operation will begin.   

Note 

•When in Auto mode the fan speed is automatically adjusted  according to the indoor air quality. As the indoor air quality  improves, the fan speed will automatically be reduced. If the  indoor air quality decreases, the fan speed will automatically  increase. 

2. Sleep Mode 

Press the Mode button to select  Sleep mode. 

•The LED “Sleep” light will indicate when  Sleep mode is activated, and operation will  begin. 

Note 

•When Sleep mode is selected, the fan speed is automatically  set to Low. The fan speed can be manually changed by  pressing the Fan Speed button, changing the unit into manual  mode. 

•When Sleep Mode is activated, the Air Quality Indicator LED  light is disabled. 

MANUAL & TIMER 

3. Manual Mode (setting fan speed) 

Users can opt to manually set the fan speed to Low, Medium, High, or  Turbo. 

① Press the Fan Speed button to set the desired fan speed.  

Note 

•When Manual Mode is selected, Auto Mode is automatically  disabled. 

4. Timer 

The timer can be set to let the unit run for a specified period of time. 

① Press the Timer button to select the desired length of time.  

•When the Timer LED light will indicate the selected length of operation. 

•Every time the Timer button is  pressed, The Timer LED light will cycle through the settings, (1hr, 4hr, 8hr, [NO TIMER]).  

PLASMAWAVE® & AIR QUALITY INDICATOR 

5. PlasmaWave® 

By default, PlasmaWave® is enabled whenever the unit is powered on. 

① Press the Plasmawave button, when the unit is on, to enable or disable this feature.    

Note 

•In Auto mode, as the indoor air quality improves, the fan  speed will automatically be reduced to Low. 

•When the unit is running, you may hear a chirping or buzzing  sound. The sound is from large particles passing through  PlasmaWave®, it is normal and does not signify product  failure. 

6. Air Quality Indicator  

When on, the LED light will indicate the current indoor air quality  according to three levels: BLUE (good), AMBER (fair), RED (poor). 

Note 

•Air quality level is displayed on the indicator, based on the  Smart Sensors. Depending on the immediate environment,  the indicator may change frequently in color or stay the same  for lengthy periods of time. 

FILTER CARE 

1. Know The Filters 

When the Check Filter indicator LED is on, it is time to replace both the  True HEPA and AOCTM Carbon Filters.  

Filter Indicator Light When to  service When to replace
Pre-filter none Clean once  every 14 days Permanent
AOCTM Carbon filter  check filter Clean once  every 3  months Lasts up to 12 months
True HEPA filter check filter Can NOT be  WASHED Lasts up to 12 months

※ Intervals between filter replacement may vary depending on environment.

※ For optimal use, Pre-filter can be cleaned once every 14 days which can extend  the life of other filters. 

To purchase replacement 

Winix filters: 

🕿(877)-699-4649 

www.winixamerica.com 

Note

•The filters’ life varies depending on the level of pollutants in  the air. The more dust present in the environment, the more  dust accumulates in the filters, shortening the life.  

•If the filters are heavily soiled or have a bad odor, or if the fan  strength is significantly weakened, replace filters even if the  Change Filter indicator has not yet turned on.  

2. Removing Filters 

Turn the unit power off before removing filters. 

① Remove the front panel by grasping its upper edge and gently pulling  forward. 

② Press on the Pre-filter tabs near the top of the filter, release and  remove. 

③ Pull out the AOCTM Carbon filter and True HEPA Filter. 

3. Preparing New Filters

① Remove replacement filters from protective plastic wrap.  

•Operating the unit without removing filters from plastic wrap may cause abnormal noise, deformation, or fire as a result of overheating. 

NOTICE 

•For optimal performance, only Winix filters should be used  with this unit. 

4. Replacing Filters 

① Insert the True HEPA Filter first, then the AOCTM Carbon filter. 

② Insert the Pre-filter. 

•Insert bottom tabs of the Pre-filter into the slots on either side of the lower   part of the unit, then rotate upward to insert the upper tabs into the slots at   the top part of the unit until sides audibly click into place. 

③ Replace the front panel by first inserting the latch at the bottom  edge into the base of the unit, then rotate the panel upward toward  the top of the unit until the magnets pull the lid closed. 

5. Resetting The Unit 

After replacing the filters, turn the power onto the unit and then use a thin object, such as a paper clip, to press the RESET switch for 5 seconds.    

6. Cleaning the filters 

Intervals between filter cleaning may vary depending on the air quality. 

① When cleaning the AOCTM Carbon Filter, remove it from the unit, and hold it under running room temperature water.   

•Do not use detergent or soap. 

•Allow the filter to dry for 24 hours or more before using.   

② Use a vacuum cleaner or soft brush to clean the Pre-filter. If it is excessively soiled, rinse in room temperature water.   

•Do not use detergent or soap. 

•Allow the filter to dry for 24 hours or  more before using.  

※ If the pre-filter becomes damaged or in any way needs replacement:  

Please contact Winix 

🕿(877)-699-4649 

www.winixamerica.com

NOTICE 

  • •Do not use benzene, alcohol, or other volatile fluids, which  may cause damage or discoloration. 
  • •The Pre-filter and AOCTM Carbon are both reusable after  cleaning, ensuring they are completely dry.  
  • •Do not use hot water over 104oF or volatile fluids such as  paint thinner.  
  • •After washing the filter, allow it to dry completely in a well  ventilated area. Otherwise, it may develop a bad odor. 

CLEANING CARE 

2. Cleaning the Exterior & Interior 

① Wipe with a soft damp cloth using room temperature water. Afterwards, wipe it down with a  clean dry cloth. 

•To keep unit in peak condition, clean every 1-2 months.   

① Open the front panel and clean the interior with a vacuum cleaner. 

•For optimal performance, clean every 1-2 months.  

NOTICE

  • •When cleaning the unit, always unplug the power cord first  and then wait until the unit has cooled down. 
  • •Never disassemble, repair, or modify this unit yourself.
  • •Do not use flammable sprays or liquid detergents.
  • •Do not allow children to clean or maintain the unit.
  • •Before cleaning or maintaining, ensure unit is unplugged. 

REMOTE CONTROL

Operates in a 20 foot radius. 

( A ) Power: Turns the unit on or off.

( B ) Auto: Enables Auto Mode. 

( C ) Fan Speed: Enters into Manual Mode  while selecting Fan Speed. 

( D ) Turbo: Enters Manual Mode setting  device directly to Turbo Fan Speed. 

Cradle 

Wall mountable storage cradle. 

Battery Replacement 

① Squeeze tabs of battery cover  while pulling on the remote. 

② Remove old battery. 

③  Insert new battery, with PLUS side  up. 

  • Always use CR2025 3V lithium  battery. 
WARNING 
– Incorrect battery usage may cause battery fluid leakage  and/or damage.  
– When not using remote for extended periods of time,  remove the battery. 
– Avoid dropping or damaging the remote.

FREQUENTLY ASKED QUESTIONS

 Problem  Check / Actions to take 
 It does not turn on at all. •Is the plug securely attached to the outlet?
Make sure the outlet has power going to it, and ensure the plug is secured.
•Is there a power outage?
Check to see if other lights and electrical equipment are working and try again.
 It doesn’t work in Auto Mode. •Has Auto Mode been selected?
Press the Mode button until Auto Mode is selected.
•Is the sensor blocked or clogged?
Wipe Odor Sensor with wet cloth, then dry.
 It vibrates and makes a lot of noise. •Is it running on a slanted or uneven surface?
Move the unit to a hard, flat, even area of the floor.
 The power plug and outlet feel hot. •Is the plug securely plugged in?
Make sure the plug is properly plugged into the outlet.
 There is a strange smell. •Is it being used in a place with a lot of smoke, dust, or odors?
Clean the air intakes on either side and clean the pre-filter.
Clean or change the AOCTM Carbon filter.
The fan strength is weak.
The unit is not purifying the air.
•Is the Check Filter indicator light on?
Change the filters as required.
The display panel is dim.•Is the Light Sensor blocked by debris?
When Auto Mode is on, Sleep Mode is automatically activated when the Light Sensor detects that the room is dark.

UNIT SPECIFICATIONS 

  • Model Name: 5500-2 
  • Power Voltage: AC120V/60Hz 
  • Power Rate: 70W 
  • Room Area Served: 360ft2 
  • Dimensions: 14.9 in(W) x 7.8 in(D) x 23.6 in(H) Weight 17.6 lbs 
  • Replacement Filter : Filter H / Item: 116130 
  • Pre-Filter: Part #: 4521-0012-04 

※ The exterior, design, and product specifications may be changed without prior notice   to improve product performance.  

❖ Information regarding ENERGY EFFICIENCY RATING LABEL 

The energy costs indicated on the ENERGY EFFICIENCY RATING LABEL may differ  from your actual energy costs, depending on your energy consumption, usage  hours, and billing changes, such as utility price increases.  

Warning: Change or modifications to this unit not expressly approved by the party responsible for  compliance could void the user’s authority to operate the equipment. 

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,  pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  harmful interference in a residential installation. This equipment generates, uses and can radiate radio  frequency energy and, if not installed and used in accordance with the instructions, and may cause harmful  interference to radio communications. However, there is no guarantee that interference will not occur in a  particular installation. If this equipment does cause harmful interference to radio or television reception,  which can be dteremined by turning the equipment off and on, the user is encouraged to try to correct the  interference by one or more of the following measures. 

  • Reorient or relocate the receiving antenna. 
  • Increase the separation between the equipment and receiver. 
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or on experienced radio/TV technician for help. 

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two  conditions: 

  • This device may not cause interference; and 
  • This device must accept any interference, including interference that may cause undesired operation of the  device.

READ ALSO: Winix Air Purifier User Manual (Model AM90)

SAFETY INSTRUCTIONS 

Thank you for purchasing a Winix air purifier. This product is for household use only.  

IMPORTANT CAUTIONS FOR  USING YOUR AIR PURIFIER 

WARNING: Follow the instructions in  this manual to reduce the risk of  electric shock, short circuit, and/or fire. 

  • Do not repair or modify the unit unless  specifically recommended in this manual.  All other repairs should be completed by  a qualified technician. 
  • The plug for this unit is polarized with  one blade wider than the other. Do not  force the plug into an electrical outlet. Do  not alter the plug in any way. If the does  not fit into the outlet, reverse the plug.  If it still does not fit, contact a qualified  technician to install a proper outlet. 
  • Do not use if the power cord or plug is  damaged or the connection to the wall  outlet is loose. 
  • Use AC 120V only. 
  • Do not damage, break, forcefully bend,  pull, twist, bundle, coat, pinch, or place  heavy objects on the power cord. 
  • Periodically remove dust from the power  plug. This will reduce the risk of shock due  to humidity build up. 
  • If the power plug is damaged, it must  be replaced by the manufacturer or a  qualified technician. 
  • Remove the power plug from the outlet  before cleaning the unit. When removing  the power plug, grasp by holding the  plug itself, never hold by the cord. 
  • Remove the power plug from the outlet  when not in use. 
  • Do not handle the power plug with wet  hands. 
  • Do not operate the unit when using  indoor smoke-generating insecticides.
  • Do not clean unit with benzene or paint  thinner. Do not spray insecticides on the  unit. 
  • Do not use the unit where it is humid or  where the unit may become wet, such as  the bathroom. 
  • Do not insert fingers or foreign objects  into air intake or outlet. 
  • Do not use use the unit near flammable  gases. Do not use near cigarettes, incense,  or other spark-creating items. 
  • Unit will not remove carbon monoxide  emitted from heating appliances or other  sources. 

IMPORTANT PRECAUTIONS FOR  USING YOUR AIR PURIFIER

  • Do not block the intake or outlet vents.
  • Do not use near hot objects, such as a  stove. 
  • Do not use where the unit may come into  contact with steam. 
  • Do not use the unit on its side. 
  • Keep away from products that generate  oily residue, such as a deep fryer. 
  • Do not use detergent to clean the unit.
  • Do not operate without a filter. 
  • Do not wash and reuse the True HEPA  Filter. 
  • Hold the handle on the back of the unit  to transport. 
  • Do not hold by the front panel. 
WARNING
This product contains chemicals  known to the State of California to  cause cancer and birth defects or  other reproductive harm.

PRODUCT WARRANTY

The terms of the warranty are as follows. 

  1. 1. This product is manufactured under stringent quality control and  inspections. 
  2. 2. Warranty void if product failure is a result of negligence or misuse by the  consumer, shipping and service fees may be incurred even during the  warranty period.  
  3. 3. The warranty must be presented upon bringing the product for service. 
  4. 4. Store the warranty in a safe place, as it cannot be reissued. 
  5. 5. This warranty is valid only in the USA and Canada. 
Product NameAir Purifier 
Model Name5500-2 
Purchase Date 
Warranty period One (1) year
Place of purchase 
Place of purchase Tel. 
Customer 
Address
Name
Tel.

※ After purchase, be sure to complete all of the above information.  

Contact for product  related inquiries and  customer service 

Developed in partnership with  

Drexel University  

(Philadelphia, PA, USA)  

162502 Rev.A 

To expedite service, please specify the model name and number, the  nature of the problem, your contact information, and your address. ● Dedicated Call Center : 🕿(877) 699-4649 

Website : www.winixamerica.com 

You can download the PDF version of the Winix Air Cleaner User Manual (Model 5500-2 ) here.