by IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.
When using an electrical appliance, basic precautions should be observed, including the following:
WARNING To reduce the risk of fire, electric shock, or injury:
» Unplug from electrical socket when not in use and before cleaning, maintaining or servicing the appliance.
» This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children without supervision.
» Children should be supervised to ensure that they do not play with the appliance.
» If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
» Do not run appliance over cord.
» Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts of the appliance and its accessories.
» Use only the type and amount of liquids specified under the Operations section of this guide. » Do not leave appliance when plugged in.
» Always connect to a properly earthed electrical socket. Do not modify earthed plug.
» Do not allow to be used as a toy.
» Use only as described in the user guide.
» Use only manufacturer’s recommended attachments.
» Do not use with damaged cord or plug. » Do not immerse in water or liquid. Use only on surfaces moistened by the cleaning process.
» If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water; do not attempt to operate it and have it repaired at an authorized service center.
» Liquid must not be directed towards equipment containing electrical components.
» Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord around sharp edges or corners.
» Keep cord away from heated surfaces.
» Do not unplug by pulling on cord.
» To unplug, grasp the plug, not the cord.
» Do not handle plug or appliance with wet hands.
» Do not put any object into openings.
» Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
» Turn off all controls before unplugging.
» Use extra care when cleaning on stairs.
» Do not use to pick up flammable or combustible liquids, such as petrol, or use in areas where they may be present.
» Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.)
» Do not use appliance in an enclosed space filled with vapors given off by oil base paint, some mothproofing substances, flammable dust, or other explosive or toxic vapors.
» Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
» Keep appliance on a level surface.
» Do not carry appliance while in use.
» Unplug before attaching the TurboBrushTM tool.
» Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
» If your appliance is fitted with a nonrewireable BS 1363 plug it must not be used unless a 13 amp (ASTA approved to BS 1362) fuse is fitted in the carrier contained in the plug. Spares may be obtained from your BISSELL supplier. If for any reason the plug is cut off, it must be disposed of, as it is in electric shock hazard should it be inserted into a mains socket.
» Do not expose to rain. Store indoors.
» Always install float before any wet pick-up operation.
» Plastic film can be dangerous. To avoid danger of suffocation, keep away from children.
» Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
SAVE THESE INSTRUCTIONS
FOR OPERATION ON A 220-240 VOLT A.C. 50-60 HZ POWER SUPPLY ONLY.
This model is for household use only.
Quick Start Guide
Check assembly guide on www.bissell.com
WARNING: Do not plug in your deep cleaner until you are familiar with all instructions and operating procedures.
Your deep cleaner comes in four easy-to-assemble components and an accessory bag.
• Base
• Upper Handle
• Clean Water Tank
• Carry Handle
A Phillips screwdriver is required for Assembly in Step 3.
- First, insert the (aluminum) Upper Handle at the top of th bease until you hear a “click”. Do NOT put the clean tank on the machine until Step 5.
2. Next, align the carry handle with the slots on either side of the base (behind the power switch and cleaning mode switch). The carry handle will “click” into place.
3. Use a Philips screwdriver to secure the screw (found taped to upper handle) into the carry handle.
4. Wrap the cord around the carry handle and Quick ReleaseTM Cord Wrap hook.
5. At the bottom of the upper handle, align the clean water tank with the grooves and slide the tank into place.
Thanks for buying a BISSELL carpet cleaner!
We love to clean and we’re excited to share one of our innovative products with you. We want to make sure your carpet cleaner works as well as it does today for years to come, so this guide has tips on using, maintaining, and if there’s a problem, troubleshooting. In just a few simple assembly steps, you’ll be ready to deep clean. Flip to the Quick Start Guide page and let’s get started!
Package Contents
Getting to Know Your Deep Cleaner
Cleaning Formulas
WARNING: To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the deep cleaner.
Keep plenty of genuine BISSELL formula on hand so you can clean whenever it fits your schedule.
Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning formulas may harm the machine and may void the guarantee.
ONLY BISSELL Wash & Protect formulas protect from future stains with ScotchgardTM Protector. ScotchgardTM is a trademark of 3M®. *60 mL of 2X concentrated formula is equivalent to 120 mL of non-concentrated formula.
Tips Before Carpet Cleaning
•If cleaning an entire room, consider moving your furniture to another area.
• Remove loose dirt and impediments.
• Pre-treat stains with BISSELL PreTreat to improve performance on tough stains and ground-in dirt.
Filling Your Clean Water Tank:
2X Concentrated Formula
| FORMULA FILLING INSTRUCTIONS | DEEP CLEAN MODE | EXPRESS CLEAN MODE |
| BISSELL 2X Concentrated Formulas | Fill water to the Water Fill Line, then add 74 mL of formula. | Fill water to the Water Fill Line, then add 37 mL of formula. |
NOTE: Fill with hot (140°F/60°C MAX) tap water and add the appropriate BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR TANK IN MICROWAVE. Do not substitute BISSELL Cleaning Formula with other household cleaning products.
NOTICE: Do not over wet carpet. Be careful not to run over loose objects or edges of area rugs. Stalling the brush may result in premature belt failure.
Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning solutions may harm the machine and may void the guarantee.
Cleaning Your Carpet
- Plug into a properly earthed outlet.
2. Select cleaning mode:
Deep Clean
Delivers a deep clean to your carpet.
Express Clean
Provides a lighter clean with about 1 hour of dry time.
3. Press the power button to turn the machine on.
To recline your machine for use, press the recline pedal with your foot.
4.
Deep Clean Mode:
- Press the spray trigger to apply solution while making 2 slow wet passes – 1 forward and 1 back.
- Release the trigger.
- Make 2 slow dry passes – 1 forward and 1 back, to suck up the dirty solution. (Do not hold down the trigger for this step.)
NOTE: For best cleaning performance, clean with your machine in Deep Clean Mode.
Express Clean Mode:
- Press the spray trigger to apply solution while making 2 wet passes – 1 forward and 1 back.
- Release the trigger.
- Make 2 dry passes – 1 forward, 1 back to suck up the dirty solution. (Do not hold down the trigger for this step.)
NOTE: In Express Clean Mode, the dirty tank will not get as full as when cleaning with Deep Clean Mode.
NOTICE: To prevent damage to Berber carpets, avoid repeated strokes in the same area.
Bare Floor Cleaning*
*Select models only
WARNING: To reduce the risk of fire and electric shock when cleaning a hard floor, the BISSELL bare floor tool must be used and is only to be used with BISSELL Wash & Shine Hard Floor Cleaner formula intended for use with this appliance.
NOTE: The bare floor tool that is compatible with the ProHeat 2X Revolution may not be included. It is available for purchase by contacting our team by phone or visting us online at BISSELL.com.
- With the machine unplugged, attach the bare floor tool to the bottom of the machine by lining the tool to the edge of the nozzle. Rotate down until it clicks into place.
Follow filling instructions and switch cleaning mode to Express Clean.
2. Plug into a properly grounded outlet and press the power button.
Clean by pressing the trigger for 1 wet pass forward, 1 wet pass back, and then release the trigger and make 1 dry pass forward, 1 dry pass back.
3. When finished, unplug the machine and remove the bare floor tool by rotating the tool up to unhook from the nozzle.
Rinse and let dry before storing. Refer to page on emptying the dirty water tank. Refer to page on cleaning your machine before storing.
Area Rug Cleaning
Important! Please check manufacturer’s tag before cleaning area rugs for any specialized cleaning instructions. We do not recommend deep cleaning delicate, silk, wool, antique or area rugs without a manufacturer’s tag.
Regularly clean your high-traffic area rugs in Express Clean Mode:
• Check the manufacturer’s tag.
• Select Express Clean Mode.
• When cleaning area rugs, place the rug on a sealed surface to test for colorfastness in an inconspicuous area. Your cleaner should not be used on unsealed surfaces.
• Important: Keep the foot of the deep cleaner perpendicular to the rug’s edge with each cleaning pass to prevent damage.
Cleaning with Hose & Tool
NOTE: If using the Deep Reach Tool (select models only) or Pet Stain Tool (select models only) be sure the needles of the tool are pressed down into the carpet so the spray gets into the carpet fibers.
Cleaning with CleanShot®
- Press the CleanShot® button with your foot. The window of the button will be green and show an “I” symbol when it is on.
2. Spray will continue until you turn it off. To turn CleanShot® off, press the button with your foot. The window of the button will be red and show an “O” symbol when it is off.
Completely cover the stain with CleanShot® spray. Allow the stain to soak. To extract, maneuver the foot of the machine over the stain to brush and remove.
NEW! 2-in-1 Pet Upholstery Tool
*Make sure your clean tank has water & formula to use the tool in wet mode..
- Follow hose plug-in instructions from steps 1 & 2
2. Attach the tool and select dry mode to first pick up dry debris and pet hair. The suction will be at the lower part of the tool, near the dry cup.
DRY MODE NOTE: Use a “raking” motion to clean. Start with the tool farthest away and rake in small increments as you bring the tool toward you. The rubber
nubs will help attract hair to the suction channel.
WET MODE NOTE: Start from the area farthest away. Hold the trigger down, and pull the tool toward you. Keep the tool in contact with the surface as you pull. You will see extraction through the nozzle.
Empty Dirty Water Tank
WARNING: To reduce the risk of fire, electric shock or injury, turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting.
- To release dirty water tank, press down on the colored tank handle.
2. Tilt the tank slightly toward you.
3. Grab the handle and tank with both hands and pull the dirty water tank up and away to remove.
4. For quick empty: Pull the rubber tab and tilt to pour. (Located at the corner of the top of the tank.)
When closing the rubber tab, make sure all edges are sealed tight.
For final clean and rinse: Unscrew the ring at the bottom of tank.
Gently remove the float stack, rinse, and clean.
Once clean, return float stack into the tank by lining up the arrows so they point at each other. This is the only way the float stack will fit into the tank.
With the arrows aligned, the float stack should lock into place.
Return the ring and twist to lock. Water may leak if the ring is not fully tightened.
5. Clean the red filter below the dirty tank by wiping off any remaining dirt or debris.
6. To return the dirty tank: Angle the tank and insert bottom first. Then tilt the tank toward the machine and push the top in until it clicks into place.
Cleaning Machine After Use
WARNING:To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.
First, fill the clean water tank with warm tap water and then empty it all to rinse. Then fill again with warm tap water and return the tank to the machine.
Twist cap back on tightly.
To flush and rinse the machine: Turn the machine on and press the trigger for 15 seconds while making back and forth passes on a section of carpet.
Finally, release the trigger and extract the water.
See page on how to clean the dirty tank from the water that was just extracted.
Empty the clean water tank and let dry before storing.
Wipe your machine’s exterior with a soft cloth.
Store machine in a protected dry area.
NOTICE: To reduce the risk of a leaking condition, do not store unit where freezing may occur. Damage to internal components may result.
Brush Roll & Nozzle Care
WARNING: To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.
NOTE: Be sure to clean the brush rolls and nozzle before storing your machine. Follow these steps if your nozzle becomes clogged with hair or debris.
2. Remove the nozzle from the foot: scoop and grip the Accessory Hose Door. Firmly pull up to remove the nozzle.
3. Pull forward the nozzle wire on the front of the brush roll cover for release.
4. To reveal the brush rolls. Press on the two release buttons and lift straight up.
5. At this point, the nozzle and brush roll cover can be rinsed under running water and the nozzle clean out tool can be inserted to unclog hair or debris.
6. Use the comb to brush out the debris or hair from the brush rolls.
7. When finished, return the brush roll cover by pushing it straight down. You will hear a click from each “push” button when the cover is pushed down into place. Ensure the nozzle wire on the front of the brush roll cover has also snapped back into place. Line up the nozzle from the edge near the floor and rotate to snap back into place.
Replacing Belts & Brush Rolls
WARNING: To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.
What you will need: 1 Phillips screwdriver & 1 flathead screwdriver
- While the machine is upright, unplug the machine and remove both tanks. Remove the nozzle and brush chamber cover (see steps in Brush Roll & Nozzle Care). Press the recline pedal and lay the machine on its back.
2. With the machine laying on its back, locate the belt access plate. Use a Phillips-head screwdriver to remove the belt access plate screw.
3. Remove the Belt Access Plate.
4. With the machine still on its back, use a Phillips-head screwdriver to remove the screw on the brushroll end cap.
5. If the Gear Belt is broken, gently remove it. If you are replacing your brush rolls, gently remove the belt.
6. There are washers on both ends of the brush rolls, be careful that these do not fall off or get lost.
7. Use a flathead screwdriver and press it into the Belt Access Door slot. Lift to remove the Belt Access Door.
8. Turn the machine on its side and use a Philips screwdriver to remove the screw just underneath the wheel.
Slide the wheel down to remove.
NOTE: To replace brush rolls, remove them from the metal posts and replace. Make sure the metal post goes completely through the end of the brush roll. The brush roll bristles should be aligned in a ‘V’ pattern as pictured.
Align brush rolls with belt at other end. To ensure alignment, hold the end of one brush roll and twist.
The other brush roll rotates with it.
Check that washers are in place.
Reassemble the belt and end cap, securing with screws you removed.
9. If the flat belt is broken, gently remove the belt.
If it needs replacing for any reason, the gear belt should already be removed before removing the flat belt.
Rotate the machine back to its side. Feed the new flat belt through the opening so that it wraps around the red pulley.
10. Keep it wrapped on the red pulley and adjust the machine so it is laying on it’s back again. Use your thumb to stretch the flat belt back to wrap around the metal axle.
11. Resecure the Belt/Brush Access Plate:
Slide the wheel up back into the slot and secure with the screw that was removed.
12. Snap the Belt Access Door back down into place.
NOTE: See Step 7 on how to put the brush roll cover and nozzle back in place.
Troubleshooting
WARNING: To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.
You can download the PDF version of the Bissell PROHEAT 2X® REVOLUTION PET PRO VACUUM CLEANER USER GUIDE (2066 SERIES) here.