Array Smart Deadbolt User Manual

Array Smart User Manual
Smart Doorlocks

Installation Instructions



• Remove the battery from the battery compartment and charge it in the  Charging Cradle until the LED turns green. 

• The ARRAY lock has a built-in solar panel that will charge the battery if  positioned in direct sunlight. If unable to position the lock in direct  sunlight, you may need to charge the battery more frequently. You will see  the battery status on the app. 

• Do not attempt to disassemble any internal components of the lockset.  You will void the warranty. 

• Do not install the battery until you’ve installed the lock and downloaded  the app. Follow the instructions in order. 

• Do NOT use a power drill to install the lock. A power drill should only be  used for door preparation. 

• Make sure your door is properly aligned and can be closed without  pushing, pulling or lifting the door. 

Compatible Devices: 

Note: New devices will continue to be added to enhance your experience with  the ARRAY lock. Please visit our website for a complete  list of compatible devices.

Installation Overview

Pre-Installation Instructions

1. Charge Battery

a. Remove the Battery Cover (L), Rechargeable  Battery (J), Battery Charging Cradle, USB Cable  and Wall Adapter. Remove the plastic tab on the  Battery (J). Slide the Battery (J) into the Charging  Cradle from the side. Charge the Battery (J) until  the LED Light turns from red to green.

b. Carefully remove the Antenna  Cover (K) by gently pulling the  edges outward slightly and lifting

2. Watch the Installation Video

The ARRAY lock is compatible with either iOS® or Android™ devices. Search for  “ARRAY Lock” at the App Store or Play Store to download the free app. Once the  app is downloaded, register your lock and watch the installation video. Install your  ARRAYlock (Steps 3 – 5) and then follow the instructions to add a lock or visit

3. Prep the Door • FITS DOORS 1-3/8″ (35 mm) TO 1-3/4″ (45 mm) THICK •

a. If replacing an existing deadbolt. Remove the old hardware and begin at STEP 4.

b. If installing ARRAY on a new door, follow the door preparation instructions later in this piece and use the template provided on the page that follows the instructions. 

4. Install Latch and Strike Plate

Install Strike Plate (N) in the Door Frame

Determine the Proper Faceplate

Set the Latch Backset

The distance from the center of the bore hole to the edge of the door is called the backset. If the backset of your  door is 2-3/8″, you don’t need to adjust the latch. The backset is preset for 2-3/8″. 

If the backset of your door is 2-3/4″, you’ll need to adjust the latch as shown.

Install the Latch

CAUTION: Be sure the latch is in the upright position.

5. Install Lock Assemblies

A. Door Bore Hole Options

B. Remove Mounting Plate Remove Mounting Plate Screw

Use a wrench and in a counter-clockwise motion,  remove the Mounting Plate Screw (BB). 

C. Remove Mounting Plate

Use a flathead screwdriver to remove the Mounting Plate.

D. Apply Gasket

E. Power Cable (E) goes underneath the latch. Insert Tailpiece (D) horizontally 


F. Bulged part of the Interior Mounting Plate (H)  must be toward the door.

G. Feed Power Cable (E) through Interior Mounting Plate (H) as shown. Insert Mounting Screws (AA) and  Mounting Plate Screw (BB) as shown and tighten. 


H. Install the Power Cable (E) firmly into the Connector Port.


I. Secure the Power Cable (E) onto the  Interior Mounting Plate (H) as shown.

J. Align the Tailpiece Receiver (M) of the Interior Assembly (I) into the Tailpiece (D). 

K. Insert the two Battery Compartment Screws (DD)  and tighten. Insert the Interior Housing Screw (CC)  and tighten.


Take care not to damage the antenna when  inserting the Battery Compartment Screws (DD).

L. Re-install the Antenna Cover (K) by gently separating  both sides of the Cover (K) and snapping the Cover  (K) onto the side ridges of the Interior Assembly (I).  Apply Screw Cover (Q)

6. Return to the app and follow the instructions to Add a Lock

Door Preparation Instructions for New Doors

If installing ARRAY on a new door, follow the door preparation  instructions and use the template given.

Mark Door with Template

a. Mark the centerline for the deadbolt about 44″  (1120 mm) from the floor, or about 5-1/2″ (140 mm)  above the center of an existing knob or lever.

bApply the template to the door with the dotted  fold line on the door edge. 

c. Select the 2-3/8″ (60 mm) or 2-3/4″ (70 mm) backset and mark the center for the hole for the deadbolt on the door face. (Most residential doors
have a 2-3/8″ backset.)

d. Mark the center for the latch hole on the door edge according to the thickness of your door.

Drill Holes

a. Drill a 2-1/8″ (54 mm) hole on the door face from both sides to avoid splitting wood.
b. Drill a 1″ (25.4 mm) hole in the door edge for the latch.

c. Insert latch into hole, mark outline of faceplate, and chisel 1/8″ (3 mm) deep or until the faceplate is flush with the door edge.

d. Mark latch screw holes and drill two 1/8″ (3 mm) pilot holes for the Latch Screws.

Prepare Door Jamb for Strike Plate

a. Mark centerline on the door jamb exactly opposite  the latch hole in the door edge. Make sure that the  mark is correct so that the latch bolt will enter the  strike plate without intereference when the deadbolt  is locked.

b. Using the strike plate as a pattern, drill the latch and screw holes, and chisel out a mortise until the strike plate fits flush.




Misusing the battery may cause it to get hot, explode, or ignite and cause injury. Follow the safety rules listed below: 

o Do not place battery in fire or heat the battery. 

 o Do not penetrate the battery with nails, strike the battery with a hammer, step on the battery, or otherwise subject it to  strong impacts or shocks. 

 o Do Not Open, Crush, Heat Above 60°C (140°F), or Incinerate.  

 o Do not solder directly onto the battery. 

Do not disassemble or modify the battery. The battery contains safety and protection devices which, if damaged, may cause the  battery to generate heat, explode, or ignite. 

Do not place the battery on or near fires, stoves, or other high-temperature locations. 

 o Do not place the battery in direct sun or use or store the battery inside hot conditions. 

 Doing so may cause the battery to generate heat, explode, or ignite.  

Immediately discontinue use of the battery if, while using, charging, or storing the battery, it emits an unusual smell, feels hot, or  appears abnormal in any other way. 

In the event that the battery leaks and the fluid gets into one’s eye, do not rub the eye. Rinse well with water and immediately  seek medical care. If left untreated, the battery fluid could cause damage to the eye. 

The temperature range for using the battery is -10°C to 60°C (14°F to 140°F). Use of the battery outside of this temperature  range may damage the performance of the battery or may reduce its life expectancy. 

Do not use the battery in any device except the BRINKS HOME SECURITY ARRAY Smart Deadbolt. 


This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful  interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits  are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can  radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio  communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful  interference to radio or television reception, which can be determined by turning the equipment o  and on, the user is encouraged to try to correct  the interference by one or more of the following measures: 

• Reorient or relocate the receiving antenna, or increase the separation between the equipment and receiver. 

• Connect the receiver to a di erent outlet. 

• Consult Hampton Products International Corporation or an experienced radio/TV technician for help. 

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the  equipment (i.e. any changes or modification that may influence the specification of radio frequency relating to the Wi-Fi® is prohibited). FCC ID Number: 2ANTYA2350X 

Wi-Fi® is a required trademark of Wi-Fi Alliance®.

WARRANTY – Full Lifetime mechanical & finish warranty and limited one-year electronics warranty. 

Subject to the terms and conditions of this warranty, Hampton Products Int’l Corp. (“Hampton”) extends a full lifetime mechanical and finish warranty and a  limited one-year electronics warranty to the original residential user (“Original User”) of this product (“Product”) against defects in material and workmanship  as long as the Original User occupies the residential premises upon which the Product was originally installed. This warranty only applies to the Original User  of Product. This Warranty is not transferable. Upon pre-authorized return of defective Product to Hampton, Hampton may repair or replace the Product with  a new or refurbished product at Hampton’s sole discretion. 

What is NOT covered: The following costs, expenses and damages are not covered by the provisions of this limited warranty: (1) labor costs including, but not  limited to, such costs for the removal and reinstallation of Product; (2) shipping and freight expenses required to return Product to Hampton; (3) failures,  defects, or damage (including, but not limited to, any security failure or loss of data), caused by any third party product, service, or system connected or used  in conjunction with the Product, and; (4) any other incidental, consequential, indirect, special and/or punitive damages, whether based on contract, warranty,  tort (including, but not limited to, strict liability or negligence), patent infringement, or otherwise, even if advised of the possibility of such damages. Some  states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty  give you specific legal rights and you may also have other rights that vary from state to state. 

The provisions of this Warranty do not apply to Product: (i) used in commercial applications; (ii) used in common area applications; (iii) used for purposes for  which they are not designed or intended; (iv) which have been subjected to alteration, abuse, misuse negligence or accident; (v) which have been improperly  stored, installed, maintained or operated; (vi) which have been used in violation of written instructions provided by Hampton; (vii) which have been subjected  to improper temperature, humidity or other environmental conditions; (viii) which, based on Hampton’s examination, do not disclose to Hampton’s satisfaction  non-conformance to the warranty. Additionally, the limited lifetime warranty DOES NOT COVER scratches, abrasions, or deterioration due to the use of paints,  solvents or other chemicals, abuse, misuse, or Product used in commercial applications. 

Additional terms: Hampton does not authorize any person to create for it any obligation or liability in connection with the Product. Hampton’s maximum  liability is limited to the original purchase price of the Product. No action arising out of any claimed breach of this warranty by Hampton may be brought by  the Original User more than one (1) year after the cause of action has arisen. 

Exclusions: Tuscan Bronze® finish is designed to improve over time and change in appearance, creating a living finish through daily use and, thus, finish  discoloration is not applicable to the above warranty. 

For assistance or specific warranty details and limitations information, please call 1-800-850-5625 in the U.S and Canada, or visit 

You can download  PDF version of the Array Smart Deadbolt User Manual here.